Liquid-controls SP2200 Manuel d'utilisateur

8The following is a list of abbreviations as they appear on the display and front panel of the unit.ABBREVIATION DESCRIPTIONSCALING FACTOR - For A and

9DIVIDE K FACTOR BY 3600 - This sets the unit for rate per hour; equal to 3600 times rate per second.NORMALIZING FACTOR - Normalizes (averages) the da

101- COMMON2- N.O.(N.C./NPN)3- COMMON4- N.O.(N.C./NPN)5- A INPUT6- B INPUT7- 12VDC OUT/+DC IN8- -DC (GROUND)9- RESET INPUT10- NOT USED11- A.C. INPUT12

11CALCULATING SCALE FACTORSThere are two separate dividing scale factors, one for input "A" and one for input "B". The factor t

12REMARKSThis section of the menu is used to setup the scaling factors for inputs A & B.This sets the decimal for factor A.Press the arrow key und

13PRESS DISPLAY REMARKSThis section of the menu sets up thecounter and combination “C” informa-tion.This sets the decimal location for theA,B&C

14ENTERSTEP3REMARKSPRESS DISPLAYThis section of the menu is used to set upthe rate information.Press the PRGM key to choose RPS (rateper second) or SC

15DISPLAY REMARKSfactorcountratelocLC PGorLC ALLCoDEFlashesfollowed by:#####CoDEFlashesfollowed by:0LoCoruN LoCPRGMPRGMPRGMPRGMThis section of the men

16REMARKSDISPLAYPRESSPRGMPRGMPRGMPRGMPRGMSTEP5SETTINGTHERELAYSENTERENTERfactorcountratelocrelay a totora ratetot aortot cdu ##.#hy ##.#rate aorrate

17PRE APRE BPRE AFollowed by lastPRE A enteredPRE BFollowed by lastPRE A enteredPRE A = Preset A (Final Preset);The set point at which output Awill tr

SPECIFICATIONS ...1DECODING PART NUMBER...

18OUTPUT WIRINGThe following diagrams detail the connection of the relay and analog output options. Each relay consist of a form A contact(Normally O

19ANALOG OUTPUT OPTIONDescription:An optional 4-20mA (0-20mA) output has been added to the unit.The output can be programmed to track C rate or C tota

20INTERFACE CARD RS 232/422 OPERATIONRS 232/422 SET-UP:All serial communication mode changes must be donethrough serial communications. Mode change

21SERIAL INPUT COMMANDS:To get a unit on line you must address it by it's device number.This is done by typing DXX(S), XX= device number. The un

22COMPUTER HOOKUP:RS 232: When connecting the unit to a computer with RS 232communication, only three connections are needed. Theseconnections are:

23PROBLEM SOLUTIONSPOSSIBLE CAUSESTROUBLESHOOTING GUIDEPower is applied to unit but the displaydoes not light.Unit works, but occasionally the display

1 DESCRIPTION & SPECIFICATIONSDESCRIPTION:The Dual Rate Totalizer is a dual 5 digit Ratemeter 6 digitTotalizer in a 1/8 DIN package. User sele

2Example: SP2200 A 3 ASeries:6 digits counter, 5 digit ratemeter with presets and scaling.Operating Voltage:110 = 110 VAC ± 15% or 12 to

3HOW TO MOUNT THE UNITThe unit is designed to be mounted with a gasket providing a water tight seal. Two mounting brackets are provided tosecure the

4WIRING THE SP2200The rear terminal contains 12 screw terminals for connecting #14 to #28 gauge wire.The unit is controlled by a microprocessor and, t

5CONNECTING AC / DC POWERNOTE: Connect power only after other connections are finished. Do not touch the live AC power terminals! The unit hasbeen

6By pressing the VIEW button one time the user can veiw the active display. By pressing the VIEW button more thanonce the user can step through all 6

7OPERATING THE FRONT PANELA B C DERSTENTER LOCK PRE A PRE B VIEW PRGM 1 4 2 3 5Press to "reset"in operatingmode. Press to"enter"